Best Equalizer Settings for Music: A Practical EQ Guide

There is no single best equalizer setting, because the thing you are correcting is your own headphones, room and ears. There is a reliable way to find yours, and it takes about ten minutes.

Published

An equalizer changes the balance between low, middle and high frequencies. It cannot add detail that is not in the recording, and it cannot turn cheap earbuds into studio monitors. What it does well is correct a specific, repeatable problem: bass that is thin, vocals that sit too far back, treble that makes you wince after an hour.

That is why copied presets so often disappoint. A curve that fixes one pair of headphones makes another pair worse. The useful thing to learn is what each band does, so you can hear a problem and know which slider to move.

What each band actually changes

Most graphic equalizers, including the one in Melodius, use ten bands spaced an octave apart. Each slider boosts or cuts a range centred on its frequency, and neighbouring bands overlap, so a move on one is heard partly on the next.

32 Hz

What lives there
Sub-bass: the rumble under a kick drum, 808 tails, organ pedals
Too much sounds
Rumbling, and it eats volume headroom
Too little sounds
Weightless on big speakers

64 Hz

What lives there
The thump of a kick and the fundamental of a bass line
Too much sounds
Boomy, one-note bass
Too little sounds
Thin, polite bass

125 Hz

What lives there
Upper bass and warmth
Too much sounds
Bloated, muddy
Too little sounds
Cold

250 Hz

What lives there
Body of vocals, guitars and piano
Too much sounds
Muddy, 'cardboard box' sound
Too little sounds
Hollow

500 Hz

What lives there
Midrange body
Too much sounds
Honky, boxy
Too little sounds
Scooped, distant

1 kHz

What lives there
Presence of most instruments
Too much sounds
Nasal, tinny
Too little sounds
Recessed

2 kHz

What lives there
Vocal clarity and the attack of notes
Too much sounds
Shouty, harsh
Too little sounds
Dull vocals

4 kHz

What lives there
Consonants, guitar bite, snare crack
Too much sounds
Fatiguing over long sessions
Too little sounds
Muffled

8 kHz

What lives there
Sibilance and cymbal shimmer
Too much sounds
Spitty 's' sounds
Too little sounds
Dark

16 kHz

What lives there
Air and sparkle
Too much sounds
Brittle, hissy
Too little sounds
Closed-in
Rough guide. Instruments span several bands, and where a problem sits varies by recording.

Five rules that matter more than any preset

  1. Cut before you boost. If vocals sound buried, try lowering 250 Hz before raising 2 kHz. Cutting the band that masks something usually sounds cleaner than boosting the thing itself.
  2. Move in small steps. Two or three decibels is a clearly audible change. Every 6 dB doubles the signal's amplitude, so a slider at +12 dB is a very large boost, not a slightly bigger one.
  3. Lower the preamp by your biggest boost. Boosting a band can push peaks past the maximum level the audio can represent, which is heard as crackle or harshness. Pulling the preamp down by the same amount keeps headroom.
  4. Set it at the volume you actually listen at. Ears are less sensitive to bass and extreme treble at low volume, which is why a curve tuned loud sounds thin at night and one tuned quiet sounds bloated when turned up.
  5. Compare by switching the equalizer off and on. Louder almost always sounds better for a few seconds. Toggling at matched volume is the only honest test.

Starting points that work

These are the curves behind the built-in presets in Melodius, so you can see exactly what each one does rather than guessing from its name. Values are decibels per band, low to high.

Bass boost

Lows
+6 · +5 · +4
Mids
+2 · 0 · 0 · 0
Highs
0 · 0 · 0
Preamp
−4 dB
Try it for
Earbuds that sound thin

Vocal

Lows
−2 · −2 · −1
Mids
+1 · +3 · +4 · +3
Highs
+1 · 0 · −1
Preamp
−2 dB
Try it for
Singers buried in a busy mix

Small speakers

Lows
0 · +3 · +5
Mids
+4 · +1 · 0 · 0
Highs
+1 · +2 · 0
Preamp
−4 dB
Try it for
Laptop and phone speakers

Late night

Lows
−3 · −2 · −1
Mids
0 · +1 · +2 · +2
Highs
+1 · −1 · −2
Preamp
0 dB
Try it for
Quiet listening without boom

Treble boost

Lows
0 · 0 · 0
Mids
0 · 0 · +1 · +2
Highs
+4 · +5 · +6
Preamp
−3 dB
Try it for
Dark, closed-back headphones

Rock

Lows
+5 · +4 · +2
Mids
0 · −1 · −1 · +1
Highs
+3 · +4 · +5
Preamp
−3 dB
Try it for
Guitars and drums with punch
Gains in dB. Lows are 32, 64 and 125 Hz; mids 250 Hz to 2 kHz; highs 4, 8 and 16 kHz.

Fixing the common complaints

'My earbuds have no bass'
Check the fit first. An earbud that does not seal loses most of its low end, and no equalizer can put it back. With a good seal, add 3 to 5 dB at 64 Hz, a little at 32 Hz, and lower the preamp to match.
'Bass is loud but muddy'
The problem is usually 125 to 250 Hz, not the deep bass. Cut 250 Hz by 2 or 3 dB and the low end tightens up without losing weight.
'Vocals sound far away'
Lower 250 Hz slightly and raise 1 to 2 kHz by 2 dB. Avoid pushing 4 kHz: it adds clarity for a minute and fatigue for an hour.
'Everything sounds harsh after a while'
Look at 4 and 8 kHz. A 2 dB cut there often makes long sessions comfortable without making the music sound dull.
'Some songs are much louder than others'
That is not an equalizer job. Turn on volume normalization, which evens out loudness between songs. Volume normalization explains how it works and when to turn it off.

Why boosting can distort, and how players stop it

Digital audio has a hard ceiling. Most commercial music is mastered close to it, so a +6 dB bass boost can push the loudest moments past the limit, where the waveform is clipped flat. The result is a crackle on kick drums or a harshness that sounds like a bad speaker.

There are two defences. The first is the preamp: lowering the whole signal before the equalizer leaves room for the boost. The second is a limiter, which catches the peaks that still get through. In Melodius a limiter switches on automatically whenever any setting boosts the signal, and stays out of the way when nothing does, so a flat curve passes the audio through untouched.

Using the equalizer in Melodius

  1. 1

    Open the sound settings

    On the web and the desktop apps, open Account and choose Personalize, or open the full-screen player's menu and pick Equalizer & sound. On Android, go to You, then Settings, then Sound.

  2. 2

    Start from a preset

    Fifteen built-in presets cover the usual cases, from Flat and Bass boost to Vocal, Small speakers and Late night. Changes are heard immediately while the song keeps playing.

  3. 3

    Adjust the ten bands

    Each band runs from −12 to +12 dB. Bass and Treble controls add broad shelves at 100 Hz and 8 kHz for quick tone changes, and the preamp runs from −12 to +6 dB.

  4. 4

    Shape the stereo image if you need to

    Balance shifts sound left or right, useful with uneven hearing or a single earbud. On the web and desktop, Stereo width runs from mono to extra wide.

  5. 5

    Save it

    Save the curve as your own preset, up to twenty of them. Your sound settings are saved to your account.

Two further switches sit beside the equalizer. The loudness leveler evens out loud and quiet passages within a song, which helps on a noisy commute or late at night. Volume normalization keeps loudness consistent from one song to the next. Both are covered in volume normalization explained.

Frequently asked questions

What is the best equalizer setting for music?

There is no universal best, because the right curve depends on your headphones or speakers. Start flat, play a song you know well, and make small cuts or boosts of 2 to 3 dB where something sounds wrong, lowering the preamp by your largest boost.

What are the best equalizer settings for bass?

Boost 64 Hz by 3 to 5 dB with a smaller lift at 32 Hz, and lower the preamp by the same amount to avoid distortion. If the bass sounds muddy rather than deep, cut 250 Hz by 2 to 3 dB instead of boosting further.

Why does my music crackle when I boost the bass?

The boost pushes the loudest peaks past the maximum level digital audio can represent, so they clip. Lower the preamp by the size of your biggest boost. Melodius also switches on a limiter automatically whenever a setting boosts the signal.

Does Melodius have an equalizer on Android?

Yes. The Android app has the equalizer with presets, bass, treble, preamp, balance, the loudness leveler and volume normalization under You, Settings, Sound. The web and desktop apps have the same equalizer under Account, Personalize.

Should I use an equalizer with lossless audio?

You can. An equalizer changes the balance of frequencies, which is independent of whether the file was compressed. Correcting a headphone's frequency response usually makes a bigger audible difference than moving from high-quality lossy audio to lossless.

More on this topic

// Topic

Sound, equalizers and audio quality

Equalizer settings, bitrate and lossless, volume normalization and crossfade, explained.